CNC Machined Chainrings and Crank Spiders: Materials, Mounting Standards and Tooth Profiles

How custom CNC chainrings and crank spiders are made: 7075 aluminum vs steel, bolt circle diameters, direct mount, narrow-wide teeth, offset and what to send.

Last updated:

Most custom chainrings are CNC machined from 7075-T6 aluminum plate, hard or color anodized, and mounted either with bolts on a spider at a standard bolt circle diameter (BCD) or directly to the crank with a brand-specific interface. The decisions that matter for a brand are the mounting standard, the tooth profile for the drivetrain, the offset that sets the chainline, and the wear life the rider will expect.

This guide explains those decisions and how they affect machining, so you can brief a machine shop on chainrings or crank spiders without a round of avoidable prototypes.

Mounting: spider and BCD, or direct mount

A bolted chainring fits a spider, either a separate part or arms forged into the crank. The bolt circle diameter fixes which rings fit: 130 mm and 110 mm five-bolt patterns are classic road sizes, 104 mm four-bolt is a long-standing mountain bike size, and asymmetric four-bolt patterns are used on several recent cranksets. Small inner rings use smaller circles.

Direct-mount rings attach to the crank without a spider using an interface defined by the crank maker. They save weight and allow small ring sizes, but each interface is specific, so the drawing must follow that crank's published interface exactly. A crank spider, made separately, lets one crank accept standard bolted rings and is also the part that power-meter makers often replace.

Tooth profile, chain width and narrow-wide rings

Bicycle chains share the half-inch (12.7 mm) pitch, but chain width differs between single-speed and derailleur drivetrains, and tooth thickness and chamfers are designed for the chain the ring will run. Rings for front derailleurs need shifting ramps and pins; single-ring (1x) drivetrains commonly use a narrow-wide tooth pattern, alternating thick and thin teeth to fill the chain's inner and outer links and keep the chain on without a guide.

The tooth form is usually cut with a profiled cutter or milled as a 2D contour, followed by chamfers on both faces. The tooth tip and flank shape decide how quietly the chain engages and how long the ring lasts, so keep the tooth geometry as a controlled part of the drawing rather than leaving it to the shop.

Offset and chainline

The offset — how far the teeth sit from the mounting face — sets the chainline, the line between the chainring and the middle of the cassette. Wrong offset makes the chain run at a steeper angle in the outer gears, which costs efficiency and wears parts. Brands normally offer the same tooth count in several offsets for different hub and frame standards, so the drawing should state the offset as a primary dimension.

Materials, wear and finish

7075-T6 aluminum is the common material for CNC chainrings because it is strong for its weight and machines cleanly. Hard anodizing raises surface hardness and wear resistance; color anodizing is mainly cosmetic. For riders who value durability over weight — e-bikes, commuting, mud — steel rings wear much more slowly, and some brands use steel teeth on an aluminum carrier.

  • Specify the alloy and temper, and whether the finish is hard anodizing or decorative anodizing.
  • Allow for anodize build-up on the bolt holes and the mounting interface.
  • Laser marking of tooth count, BCD and logo is common; say where it goes so it does not end up on a functional face.

Flatness, runout and batch consistency

A thin ring machined from plate can move as material is removed, and an out-of-flat ring shows up as a chain that rubs or shifts unevenly. Machining sequence, fixturing and a good plate material control this. For a batch, check flatness, the bolt hole positions or interface, and the tooth profile on first articles, and keep the same material source between batches when possible.

What to send for a chainring or spider RFQ

  • The mounting standard (BCD and bolt count, or the direct-mount interface) and the crank it must fit.
  • Tooth count, tooth profile drawing, chain type and whether the ring is for 1x or a front derailleur.
  • Offset or chainline target, material, finish and colors.
  • Marking, packaging and the quantity split across tooth counts.

Chainrings and spiders at Chi Xin

Chi Xin Technology is a CNC machine shop in Nantun District, Taichung, Taiwan, founded in 2022. We run 5+ CNC machines — 4.5-axis CNC machining centers and CNC lathes — and mainly machine aluminum alloys and alloy steel, with a metal tolerance of 0.02 mm. We also offer wire EDM and surface finishing including anodizing, and we export to customers in Europe and North America.

We machine chainrings, crank spiders and other bicycle core parts. Send the tooth profile and mounting interface with your drawing, and we confirm material, finish and tolerances in the quotation.

Frequently asked questions

Why are most CNC chainrings made of 7075 aluminum?

7075-T6 combines high strength with low weight and machines cleanly. Hard anodizing improves wear. Steel is chosen when wear life matters more than weight.

What is BCD on a chainring?

Bolt circle diameter: the diameter of the circle through the chainring bolt holes. It must match the spider, for example 110 mm or 104 mm patterns.

What is a narrow-wide chainring?

A ring whose teeth alternate between thick and thin to fill the chain's outer and inner links, which helps hold the chain on single-ring drivetrains.

Can you make direct-mount chainrings?

Yes, if the drawing follows the crank maker's interface. Send the interface details and the crank model with the RFQ.

Have a drawing ready?

Upload your drawing or CAD file and get a quote.

Get a Quote
WhatsAppEmail drawings