Bottom Bracket and Crank Spindle Machining: Types, Sizes, Materials and Critical Features

Machining bottom bracket and crank spindles: common spindle types and sizes, shell standards, steel vs aluminum vs titanium, bearing seats, splines, testing.

Last updated:

A crank spindle is the axle that joins the two crank arms and runs in the bottom bracket bearings. It carries the rider's full pedalling load in bending and torsion, so it is one of the most fatigue-critical parts on a bicycle. Spindles are turned from steel, aluminum or titanium bar, often hollow, with precise bearing seats and a crank interface — a spline, taper or clamp surface — at each end.

This guide explains the spindle types buyers ask about, how spindle length and diameter relate to the bottom bracket standard, and which features a machine shop must hold for the spindle to run smoothly and last.

Common spindle types and diameters

The spindle type is set by the crankset, not by the frame. Widely used examples include 24 mm spindles (as on Shimano Hollowtech II cranks), SRAM's 28.99 mm DUB spindle, 30 mm spindles used by several crank makers, and stepped spindles such as SRAM GXP. Older and utility bikes still use square-taper spindles, and splined interfaces such as ISIS Drive exist on some cranks.

For a new crankset, the spindle diameter is a design choice that trades weight, stiffness and bearing size. For a replacement or compatible spindle, the interface has to match the existing crank arms exactly, including splines, clamp diameters and preload system.

Length and the bottom bracket shell

Spindle length follows the frame's bottom bracket shell width and the crank's design. Threaded shells such as BSA come in 68 mm and 73 mm widths, press-fit standards such as BB86 and BB92 are common on many frames, and T47 is a threaded standard with a larger diameter. Boost and wider e-bike or fat-bike frames need longer spindles or different crank offsets. A spindle-length chart from the crank maker is the starting point; your drawing then fixes the exact length and shoulder positions.

Steel, aluminum or titanium

Heat-treated alloy steel, such as chromoly grades, is the robust choice and is common on e-bikes, cargo bikes and value cranksets. Hollow 7075 aluminum spindles save weight and are widely used on performance cranks, but need generous wall thickness and careful radii at shoulders and splines because aluminum has no fatigue limit. Titanium offers good fatigue strength at low weight and is used on premium parts, at a higher machining cost.

  • Name the exact alloy, heat treatment and hardness on the drawing.
  • Specify surface protection: plating or coating for steel, anodizing for aluminum, with masking on bearing seats if needed.

Features the shop must hold

Spindles are mainly turned, with splines or flats milled or cut afterwards and a bore drilled or bored through for hollow designs. The critical features are the ones that control bearing fit and crank engagement.

  • Bearing seat diameters and their concentricity to each other, with a fit chosen for the bearing type.
  • Surface finish on bearing seats and seal surfaces.
  • The crank interface: spline form and fit, taper angle, or clamp diameter, plus the thread for the crank bolt or preload ring.
  • Shoulder positions that set axial location and chainline.
  • Fillet radii at every change in section, which are the usual starting points of fatigue cracks.
  • Straightness and runout of the whole spindle.

Safety and testing

Because a spindle failure can cause a crash, brands should test complete crank assemblies before release. The ISO 4210 series of bicycle safety standards includes test methods for pedals and drive systems; many brands also run their own fatigue tests. A machine shop makes the part to the drawing and inspects the dimensions; validating the design and the test results remains the responsibility of the brand.

What to send for a spindle RFQ

  • Drawing and 3D model with bearing seat fits, interface details and fillet radii.
  • Crank model or interface standard, and the bottom bracket the spindle will run in.
  • Material, heat treatment, hardness and surface finish requirements.
  • Quantity, prototype count and any inspection data you need with the parts.

Spindles at Chi Xin

Chi Xin Technology is a CNC machine shop in Nantun District, Taichung, Taiwan, founded in 2022. We run 5+ CNC machines — 4.5-axis CNC machining centers and CNC lathes — and mainly machine aluminum alloys and alloy steel, with a metal tolerance of 0.02 mm. We also offer wire EDM and surface finishing including anodizing, and we export to customers in Europe and North America.

We machine bottom bracket spindles and other bicycle core parts on our CNC lathes and machining centers. Send the drawing and interface details, and we confirm material, finish and tolerances in the quotation.

Frequently asked questions

What are the common bottom bracket spindle sizes?

Widely used examples are 24 mm spindles (as on Shimano Hollowtech II), SRAM DUB at 28.99 mm, 30 mm spindles and stepped designs such as SRAM GXP. Square-taper and splined spindles are still found on older and utility bikes.

How is the right spindle length chosen?

From the bottom bracket shell standard and width (for example BSA 68 or 73 mm), the crank design and the chainline. Start from the crank maker's spindle chart, then fix the exact length on the drawing.

Is an aluminum spindle strong enough?

Hollow 7075 spindles are common on performance cranks, but need adequate wall thickness and generous fillets because aluminum fatigues over time. Steel is the more robust choice for e-bikes and cargo bikes.

Who is responsible for fatigue testing?

The brand that designs and sells the crankset. The machine shop produces parts to the drawing and checks the dimensions; the design should be validated with tests such as those in the ISO 4210 series.

Have a drawing ready?

Upload your drawing or CAD file and get a quote.

Get a Quote
WhatsAppEmail drawings