How to Specify Surface Roughness (Ra) on CNC Drawings

How to specify surface roughness on CNC drawings: Ra 0.4–6.3 µm and what reaches them, Ra vs Rz, µin conversion, ISO 21920-1 and ASME B46.1 symbols, anodizing.

Last updated:

For most CNC parts, Ra 3.2 µm (125 µin) is the normal as-machined default, Ra 1.6 µm (63 µin) a fine machined finish for sealing faces and fits, and Ra 0.8 µm (32 µin) or below a precision finish that may need extra passes or grinding. Specify a tighter value only on the surfaces that need it, and put a general value in the title block for the rest.

Roughness callouts are cheap to write and expensive to over-specify: every step down in Ra can mean slower feeds, extra finishing passes, a different process or an extra inspection. This guide explains the common values, how Ra relates to Rz and microinches, which standards define the symbol, and how coatings such as anodizing change the result.

Common Ra values and what typically reaches them

Ra is the arithmetic mean deviation of the profile from its mean line. The values below follow the preferred series used on drawings; process ranges are typical for good shop practice and vary with material, tooling and part rigidity.

  • Ra 6.3 µm (250 µin): roughing or non-critical surfaces; clearance faces, hidden surfaces. Achieved easily by milling and turning.
  • Ra 3.2 µm (125 µin): standard machined finish, visible tool marks; general default for CNC parts.
  • Ra 1.6 µm (63 µin): fine machining; O-ring static sealing faces, bearing housings, cosmetic surfaces. Normal for finish turning and finish milling with sharp tools.
  • Ra 0.8 µm (32 µin): precision turning or milling at low feeds; sliding fits, dynamic seal grooves, bearing seats. Feasible on lathes in aluminum and steel, often with a dedicated finish pass.
  • Ra 0.4 µm (16 µin) and below: usually grinding, honing, lapping or polishing, especially on hardened steel. Costly; only for shaft seal running surfaces, precision bores and similar.
  • Wire EDM: typically around Ra 0.8–3.2 µm depending on the number of skim cuts.

Ra, Rz and microinches

Ra averages everything, so a surface with a few deep scratches can still show a low Ra. Rz (ISO) is the mean of the maximum peak-to-valley heights over the sampling lengths and reacts more to scratches and burrs. Rz is common on German and European drawings; Ra dominates in North America and Asia. There is no exact conversion — the ratio depends on the profile shape — but for machined surfaces Rz is often very roughly 4–7 times Ra. Do not convert on the drawing; ask the designer which parameter matters.

Microinch conversion is exact: 1 µm = 39.37 µin. Drawings usually round to the preferred series — 0.4 µm ≈ 16 µin, 0.8 µm ≈ 32 µin, 1.6 µm ≈ 63 µin, 3.2 µm ≈ 125 µin, 6.3 µm ≈ 250 µin. The older N grades (N6 = 0.8 µm, N7 = 1.6 µm, N8 = 3.2 µm) still appear on legacy drawings.

Standards: ISO 21920-1 and ASME B46.1

ISO 1302 defined the familiar check-mark symbol for decades. It has been replaced by ISO 21920-1 (indication of surface texture), with ISO 21920-2 for terms and parameters and ISO 21920-3 for specification operators; together they replace ISO 1302, ISO 4287 and ISO 4288. One practical change: the old default "16 % rule" — where up to 16 % of measured values may exceed the limit — is no longer the default; a single limit is now treated as a maximum unless the drawing says otherwise. If your inspection plan relies on the 16 % rule, state it.

In the USA, ASME B46.1 (Surface Texture: Surface Roughness, Waviness, and Lay) defines the parameters and ASME Y14.36 the drawing symbol. The symbols look similar, but the value placement and some defaults differ, so state which standard the drawing follows in the title block.

Reading and writing the symbol

  • Basic check mark: any process allowed. With a horizontal bar: material removal required (machined). With a circle: material removal not permitted (as-cast, as-forged surface must remain).
  • Value: write the parameter and limit, e.g. "Ra 1.6". An upper limit is assumed; add "U" and "L" for upper and lower limits when both matter (rare, e.g. surfaces that must hold oil).
  • Lay symbol (=, ⊥, X, M, C, R) when direction matters — for example circular lay on a face seal, or no spiral lead on a rotary shaft seal surface.
  • Place the symbol on the surface, an extension line or a leader; it must be readable from the bottom or right of the sheet.
  • General note: "Unless otherwise specified Ra 3.2" in the title block, plus individual symbols only on the surfaces that differ.

Specify only on functional surfaces

A drawing with Ra 0.8 on every surface forces the shop to plan finishing passes everywhere, and to check every face. Most parts need fine finish on a few features: bores for bearings or bushings, seal faces and grooves, sliding surfaces, mating faces that must seal or locate. Leave the rest at the general value. If a surface is cosmetic rather than functional, say so ("cosmetic surface, no visible tool marks") instead of picking a low Ra that may not describe the look you want.

Remember that roughness and tolerance interact: an IT6 fit on a small bore with Ra 3.2 is inconsistent, because the roughness eats a large share of the tolerance. As a rule of thumb, tight fits usually need Ra 0.8–1.6.

Anodizing, plating and blasting change Ra

Finishes do not simply copy the machined surface. Type II sulfuric anodizing tends to increase Ra somewhat — finishing literature reports roughly a third to a half above the pre-anodize value for typical coating thicknesses — and hard anodizing roughens more. Bead blasting before anodizing deliberately produces a uniform matte texture with a higher Ra. Electroless nickel and thin plating follow the substrate closely.

  • State whether the Ra limit applies before or after finishing.
  • If a sealing face must stay smooth after anodizing, machine it finer than the final requirement or mask it.
  • Avoid specifying bead blasting and a low Ra on the same surface.

Surface finish at Chi Xin

Chi Xin Technology is a CNC machine shop in Nantun District, Taichung, Taiwan, founded in 2022. We run 5+ CNC machines — 4.5-axis CNC machining centers and CNC lathes — and mainly machine aluminum alloys and alloy steel, with a metal tolerance of 0.02 mm. We also offer wire EDM and surface finishing including anodizing, and we export to customers in Europe and North America.

We turn, mill and wire-EDM aluminum and steel parts and anodize them, so roughness requirements before and after finishing are part of how we plan a job; put the Ra values, the standard and whether they apply after anodizing in the RFQ and we confirm in the quotation.

Frequently asked questions

What Ra should I use if I do not know?

Ra 3.2 µm (125 µin) as the general default, Ra 1.6 µm on mating, sealing and locating surfaces, and lower values only where a seal, bearing or sliding fit requires them.

Can I convert Rz to Ra?

Only approximately; Rz is often roughly 4–7 times Ra on machined surfaces, but the ratio depends on the profile. If the function depends on scratches or peaks, specify Rz directly.

Is ISO 1302 still valid?

It has been replaced by ISO 21920-1. Older drawings referencing ISO 1302 remain readable, but note that the default acceptance rule changed from the 16 % rule to a maximum rule in the new series.

Does anodizing make the surface smoother?

No. Anodizing generally increases Ra slightly, and hard anodizing more so. Machine critical surfaces finer than required or specify the Ra after anodizing.

How is roughness checked?

Normally with a stylus profilometer on the specified surfaces, or by comparison with roughness samples for non-critical faces. If you need measured values reported, say so in the RFQ and we confirm in the quotation.

Parts we have machined

Browse custom parts →
CNC machined aluminum precision hub axle
Precision Hub Axlealuminum
CNC machined aluminum hub shell
Hub Shellaluminum
CNC machined aluminum bicycle anodized lock ring
Anodized Lock Ringaluminum
CNC machined steel bicycle bushing
Steel Bushingsteel

Have a drawing ready?

Upload your drawing or CAD file and get a quote.

Get a Quote
WhatsAppEmail drawings