To specify a knurl, state the pattern, the pitch, the knurled length and the diameter after knurling — for example "Knurl RGE 1.0 DIN 82, length 12, Ø20" on a metric drawing, or "Diamond knurl, 96 DP, raised" under ASME B94.6. Straight knurls are used for press fits into plastic or for a clean grip; diamond knurls for hand grip on knobs, caps and thumb screws.
Knurling looks simple, but it is one of the few lathe operations where the final diameter depends on how the material flows rather than on where the tool goes. Leaving the pattern or the blank diameter open is the usual cause of patchy or double-tracked knurls. This guide covers the patterns, the two ways knurls are made on CNC lathes, and what to put on the drawing.
Patterns: straight, diagonal, diamond and cross
DIN 82 gives each pattern a three-letter code. The same shapes exist in inch practice under names rather than codes.
- RAA — straight knurl, grooves parallel to the axis. Used for press-fitting into plastic or soft metal, and for a fine linear grip.
- RBR / RBL — diagonal knurl, right-hand or left-hand. Single helix; less common on its own.
- RGE — left/right-hand (diamond) knurl with points raised. The classic grip knurl on knobs and caps.
- RGV — left/right-hand knurl with points indented (sunken).
- RKE — cross knurl (axial and circumferential grooves) with points raised; RKV with points indented.
Form knurling vs cut knurling
Form (roll) knurling presses hardened wheels into the rotating part and displaces material into the pattern. It creates no chips, but the radial force is high, so slender or thin-walled parts can bend or collapse, and the diameter grows. Cut knurling uses wheels set at an angle that cut the pattern like a tool, producing chips; forces are lower and diameter growth is small, which suits CNC lathes, thin-walled sleeves and parts close to the chuck limit.
Which method a shop uses is usually their choice, but the drawing should define the result so either method can meet it. If a thin wall or long overhang is involved, mention it so the supplier can plan support or choose cut knurling.
Pitch: metric DIN 82 and inch diametral pitch
Metric knurls are specified by the linear pitch in millimetres. Common pitches run from about 0.5 to 1.6 mm; 0.8 and 1.0 mm are typical for hand-grip parts in the 10–40 mm diameter range, finer pitches for small diameters and soft materials, coarser for large knobs.
Inch knurls under ASME B94.6 are specified by diametral pitch — 64, 96, 128 and 160 DP are the standard series. The standard ties the pitch to recommended blank diameters (in 1/64 in or 1/32 in steps depending on pitch) so the wheel tracks evenly around the circumference.
- Finer pitch = smoother feel, less diameter growth, works better on small diameters.
- Coarser pitch = more aggressive grip, needs more force, more growth.
- On brass and aluminum, fine-to-medium pitches form cleanly; on stainless and hardened alloy steel, knurling forces rise sharply and cut knurling is often preferred.
Diameter growth and the blank diameter
Form knurling pushes material up as well as in, so the outside diameter grows. For a straight knurl, a common rule is that the knurled diameter ends roughly half a pitch larger than the blank; other patterns use different factors, and tool makers publish formulas per pattern. For example, a 1.0 mm straight knurl on a blank of Ø19.5 ends around Ø20.
Because of this, dimension the knurled diameter as the result you need and give it a realistic tolerance — typically a few tenths of a millimetre, not a precision fit tolerance. If the knurl must press into a mating bore, the press-fit interference is controlled by the knurled diameter, so that is where the tolerance belongs.
Knurled press-fit inserts and shafts
Straight knurls are widely used for press-fitting metal parts into plastic or die-cast housings: the ridges cut into the softer material and resist rotation. Typical design points:
- Use a straight (RAA) knurl for torque resistance; add a groove or a diamond section if pull-out resistance also matters.
- Leave a plain lead-in diameter or chamfer before the knurl so the insert starts straight.
- Specify the knurled diameter and the bore diameter together; test fit on first articles, since interference depends on the housing material.
- Knurling before anodizing is normal on aluminum; mention if the knurled area must be masked.
What to write on the drawing
- Pattern and code: "RGE" (DIN 82) or "diamond, raised" (inch drawings).
- Pitch: "1.0" mm, or "96 DP".
- Knurled length and position, with a chamfer at each end to avoid burrs.
- Diameter after knurling with tolerance; optionally the blank diameter as reference.
- Material and finish, since both affect how well the knurl forms.
- Example: "Knurl DIN 82 – RGE 0.8, Ø18 ±0.2 after knurling, length 10, chamfer 0.5×45° both ends."
Knurled parts at Chi Xin
Chi Xin Technology is a CNC machine shop in Nantun District, Taichung, Taiwan, founded in 2022. We run 5+ CNC machines — 4.5-axis CNC machining centers and CNC lathes — and mainly machine aluminum alloys and alloy steel, with a metal tolerance of 0.02 mm. We also offer wire EDM and surface finishing including anodizing, and we export to customers in Europe and North America.
Knurled caps, sleeves and grip features are turned on our CNC lathes in aluminum and alloy steel and can then be anodized; give the knurl pattern, pitch and finished diameter in the RFQ and we confirm the method in the quotation.
Frequently asked questions
What is the difference between RGE and RKE?
Both are DIN 82 knurls with raised points. RGE is a left/right-hand (diamond) pattern with diagonal grooves; RKE is a cross knurl with axial and circumferential grooves, giving a square-looking pattern.
Why does my knurl look double-tracked?
The wheel did not mesh with the grooves it made on the first revolution, usually because the blank diameter did not suit the pitch or the tool entered with too little force. Correct blank diameter and setup fix it; specifying the finished diameter lets the shop adjust.
Can stainless steel be knurled?
Yes, but forces are high and the material work-hardens, so cut knurling and finer pitches are often used. Say in the RFQ if the part is stainless and we confirm in the quotation.
Should I tolerance the knurled diameter tightly?
Not unless it is a press fit. Knurled diameters vary with material flow; a tolerance of a few tenths of a millimetre is normal for grip knurls.



