Black oxide is a thin conversion coating (around 1 µm) that gives steel a black look with almost no dimensional change, but it relies on oil or wax for corrosion protection and suits indoor, oiled parts. Zinc plating adds a sacrificial layer (typically 5–12 µm) that protects steel far better, at the cost of thickness on threads and fits. If parts live outdoors or in humid conditions, choose zinc or zinc-nickel; if dimensions are tight and the environment is dry, black oxide is usually enough.
Steel parts such as 4140 shafts, 1045 brackets and steel manifolds almost always need some finish, because bare steel starts rusting within days in humid air. This guide compares the common options and lists what to write on a drawing so the finisher does what you expect.
Black oxide
Hot black oxide converts the steel surface into magnetite. The layer is so thin that it does not change fits or threads in practice, which is why it is common on tooling, fixtures, gun parts and precision components. The corrosion resistance comes mostly from the supplementary oil, wax or lacquer applied after blackening; without it, protection is minimal. In neutral salt spray testing, oiled black oxide typically lasts only hours to a few days, far less than zinc. Common specifications are MIL-DTL-13924 and AMS 2485.
Zinc plating and passivation
Electroplated zinc protects steel sacrificially: zinc corrodes first, so small scratches do not rust immediately. The plated zinc is almost always followed by a passivate that sets the color and the corrosion life. Common specifications are ASTM B633 (thickness classes Fe/Zn 5, 8, 12 and 25) and ISO 2081, or ISO 19598 for Cr(VI)-free zinc and zinc-alloy coatings.
- Clear or blue trivalent passivate: bright silver appearance, the most common RoHS-compliant choice.
- Yellow (iridescent) passivate: traditionally hexavalent chromate, which is restricted under RoHS and REACH; trivalent yellow alternatives exist.
- Black passivate: black zinc, usually trivalent with a sealer or top coat for decent corrosion life.
- Thick-film trivalent passivates and sealers can extend corrosion life significantly over thin clear passivates.
- For export to Europe, specify “trivalent passivation, Cr(VI)-free” explicitly.
Zinc-nickel, electroless nickel and phosphate
- Zinc-nickel (typically 12–16 % nickel): much higher corrosion resistance than plain zinc at similar thickness, widely used for automotive and hydraulic parts. Specified for example to ISO 19598 or ASTM B841.
- Electroless nickel (ASTM B733, AMS 2404): a nickel-phosphorus alloy deposited chemically, so thickness is uniform even in bores and threads. Typical thickness 5–25 µm; high-phosphorus grades resist corrosion best, and the coating is hard and wear resistant. Not sacrificial, so porosity can lead to local rust on steel.
- Phosphate (zinc or manganese, MIL-DTL-16232): a crystalline conversion coating that holds oil and paint. Manganese phosphate is used for wear and break-in on sliding parts; zinc phosphate as a paint base or with oil for mild protection.
Corrosion resistance: typical salt spray ranges
Neutral salt spray testing (ISO 9227 or ASTM B117) is the usual comparison. Results depend heavily on thickness, passivate, sealer and part geometry, so treat these as rough typical ranges, not guarantees, and state your required hours in the specification:
- Black oxide + oil: hours to a few days to red rust.
- Phosphate + oil: similar order to black oxide, somewhat better with good oil.
- Zinc 8 µm + clear trivalent passivate: roughly 12–72 h to white rust and about 100–200 h or more to red rust.
- Zinc with thick-film passivate and sealer: often several hundred hours to red rust.
- Zinc-nickel 8 µm + passivate: commonly 500–1,000 h or more to red rust.
- Electroless nickel: varies widely with phosphorus content and thickness.
Thickness, threads and fits
Every coating except black oxide adds measurable thickness. On a 60° thread, the pitch diameter changes by about four times the coating thickness, so 8 µm of zinc consumes about 0.032 mm — close to the allowance of a 6g thread on mid-size metric threads. Plain diameters grow by twice the thickness.
- External threads: 6g usually accepts thin zinc (around 5 µm); for 8–12 µm, consider 6e/6f or note “6g after plating”.
- Internal threads: plating builds up less inside holes, but specify gauging after plating if it matters, or mask.
- Fitted diameters (bearing seats, H7/g6 fits): mask them, or machine undersize so the size is correct after coating.
- Electroless nickel builds evenly everywhere, including inside bores, so allow for it on every functional feature.
Hydrogen embrittlement and baking
Acid cleaning and electroplating can let hydrogen into steel. In high-strength or hardened steel, this can cause delayed brittle cracking under load, sometimes days after assembly. The usual mitigation is an embrittlement-relief bake after plating and before passivation, typically around 190–220 °C for several hours, longer for higher strength, as described in ASTM B850 and ISO 9588.
Baking is generally required for parts above roughly 31–39 HRC (the exact threshold depends on the standard you use), for example through-hardened 4140 shafts or springs. Note the hardness and the baking requirement on the drawing; pre-hardened 4140 at around 28–32 HRC sits near the threshold, so decide explicitly. Black oxide and electroless nickel carry less risk than acid electroplating but are not risk-free for very hard parts.
How to specify the finish
- Name the process and standard: “Zinc plate per ASTM B633 Fe/Zn 8, clear trivalent (Cr(VI)-free) passivate” or “Black oxide per MIL-DTL-13924 Class 1, oil”.
- Give the color, the RoHS/Cr(VI)-free requirement and any salt spray hours required.
- List masked features (threads, fitted diameters, contact faces) and say whether sizes apply before or after coating.
- State hardness and whether embrittlement-relief baking is required.
- Mention racking marks or contact points that are acceptable if appearance matters.
Steel finishes at Chi Xin
Chi Xin Technology is a CNC machine shop in Nantun District, Taichung, Taiwan, founded in 2022. We run 5+ CNC machines — 4.5-axis CNC machining centers and CNC lathes — and mainly machine aluminum alloys and alloy steel, with a metal tolerance of 0.02 mm. We also offer wire EDM and surface finishing including anodizing, and we export to customers in Europe and North America.
We machine alloy steel parts such as shafts, axles and brackets and arrange surface finishing as part of the order; tell us the finish, standard, masking and any baking requirement in the RFQ and we confirm in the quotation.
Frequently asked questions
Is black oxide rust-proof?
No. Black oxide on its own gives very little protection; the oil or wax on top does most of the work. It suits indoor, oiled or assembled parts, not outdoor exposure.
Will zinc plating affect my threads?
Yes. A coating changes thread pitch diameter by about four times its thickness. Thin zinc usually fits a 6g thread; thicker coatings need a larger allowance, masking or a note that the class applies after plating.
Is yellow zinc RoHS compliant?
Traditional yellow chromate contains hexavalent chromium and is not. Trivalent yellow, clear and black passivates are available as Cr(VI)-free alternatives.
Do hardened 4140 parts need baking after plating?
Through-hardened parts above roughly 31–39 HRC, depending on the standard, generally do. State the hardness and the baking requirement on the drawing so the plater can apply it.
Can you do zinc-nickel or electroless nickel?
Tell us the finish and specification in the RFQ and we confirm in the quotation.



