Aluminum 6082 vs 6061: Choosing and Substituting EN AW Grades for CNC Parts

EN AW-6082 vs 6061 for machined parts: EN 573 designations, T6/T651 strength, machinability, anodizing, EU vs Asian availability and substitution.

Last updated:

EN AW-6082 and 6061 are both heat-treatable Al-Mg-Si alloys and are often interchangeable for machined parts. In T6/T651, 6082 is usually slightly stronger, while 6061 tends to anodize a little more evenly. The practical difference for most buyers is availability: 6082 is the default structural plate and bar grade in Europe, while 6061 is the default in North America and Asia.

If your drawing was made in Europe and calls for 6082, a shop in Taiwan or the US will often propose 6061 instead. This guide explains when that is acceptable, when it is not, and how to write the material callout so there is no argument later.

Designations: what the names mean

EN 573 defines the European wrought aluminum designations. The numeric name (EN AW-6082) and the chemical-symbol name (EN AW-AlSi1MgMn) describe the same alloy; older drawings may show the German material number 3.2315 or the old British grade HE30. 6061 appears in Europe as EN AW-6061 / EN AW-AlMg1SiCu and in the US under ASTM specifications such as B209 (sheet and plate) and B221 (extrusions).

  • EN AW-6082: Si 0.7–1.3 %, Mg 0.6–1.2 %, Mn 0.4–1.0 %, Cu up to 0.1 %
  • EN AW-6061: Si 0.4–0.8 %, Mg 0.8–1.2 %, Cu 0.15–0.40 %, Cr 0.04–0.35 %, Mn up to 0.15 %
  • The manganese in 6082 refines the grain and gives the extra strength; the copper and chromium in 6061 do a similar job differently.

Strength in T6 and T651

T6 means solution heat treated and artificially aged. T651 adds stress relief by stretching, which is what you want for plate that will be heavily machined because it moves less when material is removed. Mechanical properties depend on product form and thickness, so compare minimums from the relevant standard, not single numbers from a marketing table.

  • 6082-T6/T651 plate, 6–12.5 mm (EN 485-2): proof stress Rp0.2 min 255 MPa, tensile Rm min 300 MPa
  • 6082-T6/T651 plate, 12.5–100 mm (EN 485-2): Rp0.2 min 240 MPa, Rm min 295 MPa
  • 6061-T6/T651 (typical minimums for plate): yield about 240 MPa, tensile about 290 MPa
  • Typical (not minimum) values: 6082-T6 roughly 270–290 MPa yield and 310–340 MPa tensile; 6061-T6 roughly 270 MPa yield and 310 MPa tensile
  • Density (about 2.70 g/cm³) and elastic modulus (about 69 GPa) are practically the same, so stiffness does not change with a substitution.

Machining and anodizing differences

In T6/T651 both alloys machine well. 6082 can produce longer chips and benefits from tools with chip breakers; 6061 is a little more forgiving and is the alloy most shops in Asia and North America have tuned their feeds and tools for. Neither is as free-cutting as 2011 or 2030, and neither should be machined in the soft O or T4 temper if you want clean threads and sharp edges.

For appearance, 6061 generally gives a more uniform clear or dyed anodize. 6082 anodizes well for protection, but the higher silicon and manganese can give a slightly greyer or less even tone, especially on color-matched parts. For hard anodizing both work; the thickness and color depend more on the process than on the choice between these two alloys.

Availability: Europe vs Asia

European stockholders carry 6082 plate, bar and tube in a wide range of sizes and often treat 6061 as a special item. In Taiwan, China, Japan and the US the situation is reversed: 6061-T6/T651 is stocked in almost every size, while 6082 may require a minimum order, a longer wait or an imported mill certificate. That is why overseas machine shops propose 6061 for European drawings — not to cut corners, but because it is the grade they can get quickly with traceable certificates.

When 6061 can replace 6082 (and when not)

  • Usually acceptable: brackets, housings, spacers, fixtures, covers and prototypes where the design has a normal safety margin.
  • Check first: parts designed close to the 6082 minimum yield, welded structures approved under a specific standard, and parts where a certificate to EN 573 / EN 485 / EN 755 is contractually required.
  • Not acceptable without engineering approval: parts in regulated products (pressure equipment, lifting gear, vehicle safety parts) where the material is part of a type approval.
  • Color-matched anodized parts: do not mix 6061 and 6082 in one assembly if the tone must match.
  • If a substitution is approved, record it on the drawing revision or the purchase order, not only in an email.

How to write the material callout

A clear callout prevents the substitution discussion entirely. Examples:

  • “EN AW-6082-T651 (EN 573-3 / EN 485-2) — no substitution” when 6082 is required.
  • “EN AW-6082-T6 or 6061-T6/T651 acceptable” when either works.
  • State whether a mill certificate (for example EN 10204 3.1) must ship with the parts.
  • Give the temper for the finished part, not only the alloy; a part machined from T6 bar and then welded is no longer T6 near the weld.

6061 and 6082 parts at Chi Xin

Chi Xin Technology is a CNC machine shop in Nantun District, Taichung, Taiwan, founded in 2022. We run 5+ CNC machines — 4.5-axis CNC machining centers and CNC lathes — and mainly machine aluminum alloys and alloy steel, with a metal tolerance of 0.02 mm. We also offer wire EDM and surface finishing including anodizing, and we export to customers in Europe and North America.

If your drawing calls for EN AW-6082, tell us in the RFQ whether 6061 is acceptable; we state the alloy and temper we will use in the quotation so the material is agreed before machining.

Frequently asked questions

Is 6082 stronger than 6061?

Slightly, in most product forms. In T6/T651 plate the EN 485-2 minimums for 6082 are around 240–255 MPa proof stress and 295–300 MPa tensile, compared with roughly 240 MPa and 290 MPa for 6061-T6. The gap is small enough that most non-critical parts can use either.

What is the US equivalent of EN AW-6082?

There is no exact US equivalent in common stock; 6082 is an internationally registered alloy but is rarely stocked in North America. 6061-T6 is the usual practical alternative, subject to the checks above.

Is HE30 the same as 6082?

HE30 is the old British designation that 6082 largely replaced. Material suppliers treat them as close equivalents, but if a drawing names HE30, confirm with the designer that EN AW-6082 is acceptable.

Will 6061 and 6082 parts look the same after anodizing?

Not always. 6061 usually gives a more even tone; 6082 can look slightly greyer. Keep one alloy per assembly when color matching matters.

Can you supply a mill certificate?

Tell us the certificate type you need in the RFQ and we confirm in the quotation which material and documentation we will supply.

Parts we have machined

Browse custom parts →
CNC machined steel fixing block
Fixing Blocksteel
CNC machined aluminum flange base
Flange Basealuminum
CNC machined aluminum hub shell
Hub Shellaluminum

Have a drawing ready?

Upload your drawing or CAD file and get a quote.

Get a Quote
WhatsAppEmail drawings